DoorKing Access Control Installation Nationwide

DoorKing Access Control Installation: The Roswell Owner’s Guide

DoorKing access control installation in Roswell typically runs $1,200-$2,800 for a complete keypad, card reader, or telephone entry system, depending on whether we’re retrofitting an existing gate operator or pulling new low-voltage cable from the house. Most Roswell installations are scheduled within 48 hours of the free site measure, and we stock DoorKing-compatible components for the 1802, 1803, 1808, and 1833 series on our van. We see this call most often after a storm: the keypad still lights up, but the gate won’t respond to any code, or the telephone entry system rings the house but never releases the strike.

Call (706) 928-9815

Which DoorKing Models This Applies To

DoorKing has manufactured access hardware since 1948, and the model numbering tells most of the story once you know how to read it. The 1802 series covers basic standalone keypads for single-family residential gates in Roswell neighborhoods like Martin’s Landing and Willow Springs. The 1803 adds proximity card capability. The 1808 telephone entry systems are what we find most often on estate properties off Woodstock Road, where visitors dial a code and the homeowner releases the gate remotely. The 1833 is the cellular-enabled modern replacement for aging 1808 units that no longer have reliable landline service.

Identification is straightforward if the enclosure is intact. Open the keypad or entry station and look for a white label on the main board: “DKS” followed by the four-digit model, then a revision letter. A “1802-EPD” is the current electronic programmable version; an “1802-080” is the older mechanical-code generation that DoorKing discontinued in 2015. We carry both OEM DoorKing boards and quality aftermarket equivalents from Linear and Security Brands for Roswell customers who need functional compatibility without the OEM lead time. The aftermarket boards fit the same cutout dimensions but may not support DoorKing’s older DKS software for programming multiple codes from a PC. If you’ve never connected your keypad to a computer, the aftermarket route saves roughly $90-$140 and carries the same one-year warranty on the electronics.

Signs Your DoorKing Access Control Installation Is Failing

• Keypad lights up but gate does not move. This usually means the access control board is sending a signal, but the relay that triggers the gate operator has burned contacts. We find this on 1802 units after seven to ten years of Georgia humidity cycling, especially where the keypad faces south and takes direct afternoon sun.
• Correct code produces three beeps and no release. The board has entered a lockout mode, either from repeated wrong-code attempts or from a failing memory chip that can no longer retain the master programming. In Roswell, we see this after power outages surge the transformer.
• Telephone entry rings the house but the gate won’t open when you press 9. The 1808’s internal relay has failed, or the two-conductor cable between the entry station and the house has developed resistance from moisture in an underground splice. We test both with a tone generator before quoting replacement.
• Intermittent operation that worsens after rain. Water intrusion at the keypad gasket or a cracked conduit fitting lets moisture reach the terminal block. The board may test fine in dry weather and fail only when condensation bridges two terminals. We photograph the corrosion pattern so you can see why replacement beats cleaning.
• System works only during cool morning hours. A failing transformer drops output voltage as it heats up in direct sun. By 2 PM the keypad may dim or the relay chatter audibly weakens. This is common on east-facing installations in Roswell where morning shade gives false confidence.

Before

After

Replacement Cost & What’s Included

Here is how DoorKing access control installation pricing breaks down for Roswell properties:

The range depends on three factors: whether we reuse existing conduit and cable, whether the gate operator needs a secondary relay board to accept the new access signal, and whether the homeowner wants us to program the system on-site or prefers to add codes later through the manual. Every installation includes the Haven Standard documentation: a photo of the wiring before we touch it, a photo of the completed terminal connections, and a written record of the part number and firmware revision installed. Under Clause 1, you get the flat price in writing before we pick up any tool. The 365-Day Done Right Promise covers all labor and hardware.

DIY or Call Us?

There is one safe check a homeowner can make before calling: verify that the gate operator itself works from its manual release or hardwired button. If the gate moves manually but not from the keypad, the problem is almost certainly in the access control circuit, not the operator mechanics.

Where DIY goes wrong is the low-voltage wiring and the programming sequence. DoorKing keypads require a specific resistance on the sense loop; too long a cable run or the wrong gauge and the board throws a fault that looks like a defective unit. The 1833 cellular systems must be paired to a carrier account before they’ll accept any codes, and the provisioning steps are not in the consumer manual. More critically, any work inside the gate operator’s control box exposes 120V AC even when the keypad is low-voltage. We have replaced more than one homeowner’s control board after a screwdriver slipped across the wrong terminals.

We are an independent service provider, not affiliated with DoorKing. If you have the model number from your label, call us at (706) 928-9815 and we’ll confirm what’s on the van before we schedule. Adrian does the phone triage himself most days.

FAQs